Installing e28 headliners sucks!!!!!!
-
- Beamter
- Posts: 9062
- Joined: Apr 13, 2006 11:18 PM
- Location: Council Bluffs, IA
- Contact:
Installing e28 headliners sucks!!!!!!
Gawd this shiznit is so frigging stupid!!!
-
- Beamter
- Posts: 9062
- Joined: Apr 13, 2006 11:18 PM
- Location: Council Bluffs, IA
- Contact:
-
- Posts: 4163
- Joined: Feb 12, 2006 12:00 PM
- Location: Richmond, VA
-
- Beamter
- Posts: 9062
- Joined: Apr 13, 2006 11:18 PM
- Location: Council Bluffs, IA
- Contact:
-
- Posts: 6135
- Joined: Aug 05, 2007 4:57 PM
- Location: 24477
I have heard the steam will heat and help stretch it, so its easier to work. THen as it cools, it shrinks and tightens up.Nebraska_e28 wrote:I have approximately 1713 binder clips holding it up now. How does the steam help?ElGuappo wrote:Steam?
Binder clips?
Like working with twine or wicker, you wind it when its wet, then as it drys it shrinks and tightens.
YMMV and PAYOR and all other caveats apply.
-
- Posts: 2689
- Joined: May 27, 2009 11:42 AM
- Location: ...
-
- Posts: 9478
- Joined: Feb 12, 2006 12:00 PM
- Location: Minneapolis
You're installing a vinyl headliner in the dead of winter in Nebraska ! Tell me you're in a heated garage with an interior temp over 80 degrees. I use to stretch vinyl awning covers over metal frames and would always wait for a nice warm day.
I watched that video of the rebirth of the Inka 2002tii in Germany. There was a segment where they fitted the headliner and the guy doing the work made a comment on how methodical one has to be, and the patience required, to fit it properly.
Hope it turns out.
I watched that video of the rebirth of the Inka 2002tii in Germany. There was a segment where they fitted the headliner and the guy doing the work made a comment on how methodical one has to be, and the patience required, to fit it properly.
Hope it turns out.
-
- Beamter
- Posts: 9062
- Joined: Apr 13, 2006 11:18 PM
- Location: Council Bluffs, IA
- Contact:
Custom made by my Aunt.BrianK wrote:Speaking of headliners, where did you get the replacement?
It's a cloth headliner, slightly lighter than canvas. With the wood stove going I had the garage up to about 70 degrees or so. After getting it clipped in place, its been sitting there for about a week now. It should be good & settled, but I have a few small spots to smooth out. Hopefully this week I can get the temp back up & glue it in place. Will see how it comes out.... I'm tempted to rip it out & replace it with something in cow print.Philo wrote:You're installing a vinyl headliner in the dead of winter in Nebraska ! Tell me you're in a heated garage with an interior temp over 80 degrees. I use to stretch vinyl awning covers over metal frames and would always wait for a nice warm day.
I watched that video of the rebirth of the Inka 2002tii in Germany. There was a segment where they fitted the headliner and the guy doing the work made a comment on how methodical one has to be, and the patience required, to fit it properly.
Hope it turns out.
-
- Posts: 1044
- Joined: Oct 31, 2011 10:43 PM
- Location: Jonesboro, Arkansas
You'd think that a moose would do a lot of damage (even a small one)!slammin_e28 wrote:Ugh....a wee moose nibbled on mine in the rear a while ago and I've been thinking of replacing it.
I now do not.
Last edited by freetoride on Jan 28, 2013 6:30 PM, edited 1 time in total.
-
- Posts: 4163
- Joined: Feb 12, 2006 12:00 PM
- Location: Richmond, VA
A neat trick is to find some duct tape that has a similar color to the headliner material on the sticky side and stick it to he back of the headliner. It won't look perfect, but it will look better than a hole.slammin_e28 wrote:Ugh....a wee moose nibbled on mine in the rear a while ago and I've been thinking of replacing it.
I now do not.
-
- Beamter
- Posts: 9062
- Joined: Apr 13, 2006 11:18 PM
- Location: Council Bluffs, IA
- Contact:
-
- Beamter
- Posts: 9062
- Joined: Apr 13, 2006 11:18 PM
- Location: Council Bluffs, IA
- Contact:
I now return you to your regularly scheduling programming.