b35 engine

[Steve Haygood]

Complete b35 engine with wiring harness ,ecu and air flow meter out of an 89 635 so the wiring harness will reach the glove box. 1000.00

adj sway bars 200.00

front strut assemblies with new strut inserts 150 each

Everything there, except sheet metal , which won't fit e28's of course anyway

for the e24 guys, the bumpers may be ok, I'll ck tomorrow

[a]

5 1/4" H4s?

[Steve Haygood]

no H4 ,BUT..... nice ellipsoids are still good to go

[Steve Haygood]

i do have reg New Hella H4 for US cars readily available however

[Jays535is]

i do have reg New Hella H4 for US cars readily available however

How much are these?

[Bill in MN]

What color's the interior?

[Steve Haygood]

interior is the tan-pearl color that came on the late e24

[gwade]

Forgive my lack of tech here. I've got a Euro 528i possibly looking to upgrade. I did a google search on this engine. It looks like a direct replacement for my car accept more displacement, the Bosch DME engine management, 211hp@5700 rpm.
The 535i or iS (M30/b34M-motronic, or M30/b35LE-jetronic motors)have 218hp@5400 rpm with the different management systems. Are these statements true? Looking at the specs, it seems the M30/b35LE-jetronic is the way to go. Maybe I should say, if someone was to pick the best replacement 3.5 bolt-in motor upgrade for a 528i, which would it be? Motronic, Jetronic, or Bosch DME? If I was to do a motor swap, I would probably look at a cam, and chip. Im in California, maybe just bore & stroke is allowable for smog reasons. Thanks

[Kyle in NO]

Steve, I could use the leather sunroof panel if it is in good shape...What about the dash? All cracked or nice?

[Bimmerguy2002]

Forgive my lack of tech here. I've got a Euro 528i possibly looking to upgrade. I did a google search on this engine. It looks like a direct replacement for my car accept more displacement, the Bosch DME engine management, 211hp@5700 rpm.
The 535i or iS (M30/b34M-motronic, or M30/b35LE-jetronic motors)have 218hp@5400 rpm with the different management systems. Are these statements true? Looking at the specs, it seems the M30/b35LE-jetronic is the way to go. Maybe I should say, if someone was to pick the best replacement 3.5 bolt-in motor upgrade for a 528i, which would it be? Motronic, Jetronic, or Bosch DME? If I was to do a motor swap, I would probably look at a cam, and chip. Im in California, maybe just bore & stroke is allowable for smog reasons. Thanks

i may have a b35 in good condition, pending permission to sell. Im in nor cal

[Steve Haygood]

leather head liner is very good, dash is not.

To change over to the b35 engine and it's engine management will require the wiring harness, which I have and will be included, and you will not have to cut and splice wiring as you would otherwise, and no I will not sell seperately unless the engine sells first

bimmerboy......start your own thread and sell your junk somewhere there, if "you have permission" ....

[photopark]

bimmerboy......start your own thread and sell your junk somewhere there, if "you have permission" ....

[gwade]

Can this motor be used with my existing '86 528i 5spd trans? Will my trans handle the new motor with a cam? A lightweight flywheel/Sachs clutch would be installed, 3:73 or 3:91 to come later.

[Steve Haygood]

Can this motor be used with my existing '86 528i 5spd trans? Will my trans handle the new motor with a cam? A lightweight flywheel/Sachs clutch would be installed, 3:73 or 3:91 to come later.

yes, your trans will work with it fine

[gwade]

What # ecu comes with the motor? Can a #176 ecu simply be plugged in without cutting & splicing? What kind of mileage is on the motor, compression/leakdown, overall condition?

[Kyle in NO]

It would have a 179 ECU, and that is the one you will want to use....

[Steve Haygood]

engine comes complete with wiring harness,ecu and air flow meter, Engine had 150k, no smoke etc, heck it was my car

[gwade]

Ballpark shipping estimates to Los Angeles?